Route goes to wrong interface (WIN7 pro 4.3.4 activeted)

thorgfi · 2017-03-22 13:29

I have 2 connection,
1) WLAN with DHCP and which is default route
2) LAN which I will config with NSM (IP and route)
The IP config goes OK but when I try to config route it goes to wrong interface (WLAN, not LAN)

Here is log and route print. So I tried to create route to int 11 which is LAN but it goes to int 12 which is WLAN.

-
[0:00] Gateway: OK
[0:00] Adapter - Refresh...
[0:02] Waiting for network...
[0:03] Adapter - Refresh: OK
[0:03] Route Table: Start
+ 10.107.0.0 255.255.0.0 10.107.46.1
[0:03] route add 10.107.0.0 mask 255.255.0.0 10.107.46.1 if 11
[0:03] OK!
[0:03] Route Table: OK

[0:03] Finish (14:03:39)

s:\Wireless>route print
===========================================================================
Interface List
17...34 f3 9a b0 74 34 ......Bluetooth Device (Personal Area Network)
15...00 a0 c6 00 00 17 ......HP lt4120 Snapdragon X5 LTE Network Adapter
14...36 f3 9a b0 74 30 ......Microsoft Virtual WiFi Miniport Adapter #2
13...36 f3 9a b0 74 31 ......Microsoft Virtual WiFi Miniport Adapter
12...34 f3 9a b0 74 30 ......Intel(R) Dual Band Wireless-AC 8260
11...30 e1 71 80 b6 df ......Intel(R) Ethernet Connection I219-V
1...........................Software Loopback Interface 1
19...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter
21...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2
20...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3
40...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #4
23...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5
41...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #6
18...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter
24...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
===========================================================================

IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.43.1 192.168.43.139 25
10.107.0.0 255.255.0.0 10.107.46.1 192.168.43.139 26
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
192.168.43.0 255.255.255.0 On-link 192.168.43.139 281
192.168.43.139 255.255.255.255 On-link 192.168.43.139 281
192.168.43.255 255.255.255.255 On-link 192.168.43.139 281
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.43.139 281
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.43.139 281
===========================================================================
Persistent Routes:
None

Last edited by thorgfi (2017-03-22 13:30)

NetSetMan Support · 2017-03-22 14:30

NetSetMan provides a UI for the native route.exe tool in Windows.
In your activation log you see the command that is used:

[0:03] Route Table: Start
           +  10.107.0.0  255.255.0.0  10.107.46.1
[0:03] route add 10.107.0.0 mask 255.255.0.0 10.107.46.1 if 11

For this feature we're basically simply forwarding your configuration to the official routing tool in Windows. The result is purely based on its internal actions that we do not have control of. If you feel that the result is wrong, you can try using that command outside of NetSetMan in a native console to verify that it has the same result. If the result is the same, then we recommend reporting the issue to Microsoft or searching for a solution regarding this issue for the route.exe tool, as we don't have control over that tool.

NetSetMan Support

#1 2017-03-22 13:29

Route goes to wrong interface (WIN7 pro 4.3.4 activeted)

#2 2017-03-22 14:30

Re: Route goes to wrong interface (WIN7 pro 4.3.4 activeted)